Restructure want de vorige was niet goed gegaan

src/Arduino/Sensors/Sensors.ino

@@ -0,0 +1,95 @@
+#include <DHT.h>
+#include <Wire.h>
+#include "Adafruit_SGP30.h"
+#include <WiFi.h>
+#include <PubSubClient.h>
+
+Adafruit_SGP30 sgp;
+
+// Definieert de pins voor de sensoren
+#define DHTPIN 4
+#define DHTTYPE DHT11
+
+#define MQ5_PIN 2
+
+#define SDA_PIN 10
+#define SCL_PIN 11
+
+DHT dht(DHTPIN, DHTTYPE);
+
+// WiFi en MQTT instellingen
+const char* ssid = "iotroam";
+const char* password = "6LAFiQVnUO";
+const char* mqtt_server = "Ip adres rasperry pi";
+const char* mqtt_topic = "sensors/data";
+
+// MQTT client
+WiFiClient espClient;
+PubSubClient client(espClient);
+
+// Functie om verbinding te maken met WiFi
+void setup_wifi() {
+  delay(10);
+  Serial.println("Verbinden met WiFi...");
+  WiFi.begin(ssid, password);
+
+  while (WiFi.status() != WL_CONNECTED) {
+    delay(500);
+    Serial.print(".");
+  }
+  Serial.println("\nWiFi verbonden!");
+}
+
+// Callback voor MQTT (niet gebruikt in deze toepassing, maar vereist)
+void callback(char* topic, byte* payload, unsigned int length) {
+  // Hier kun je reageren op inkomende MQTT-berichten
+}
+void setup() {
+  // Start de seriële monitor
+  Serial.begin(9600);
+  
+  dht.begin();
+  
+  pinMode(MQ5_PIN, INPUT);
+ 
+  Wire.begin(SDA_PIN, SCL_PIN);
+  Serial.println("SGP30 test");
+
+  // Verbind met WiFi en MQTT-broker
+  setup_wifi();
+  client.setServer(mqtt_server, 1883);
+  client.setCallback(callback);
+}
+
+void loop() {
+  float h = dht.readHumidity();
+  float t = dht.readTemperature();
+  
+  int mq5Value = analogRead(MQ5_PIN);
+
+  // Check of de sensorwaarden geldig zijn
+  if (isnan(h) || isnan(t) || isnan(mq5Value)) {
+    Serial.println("Fout bij het lezen van de sensors!");
+    return;
+  }
+
+   if (! sgp.IAQmeasure()) {
+    Serial.println("Measurement failed");
+    return;
+  }
+
+  // Print de sensorwaarden naar de seriële monitor
+  Serial.print("Luchtvochtigheid: ");
+  Serial.print(h);
+  Serial.print(" %\tTemperatuur: ");
+  Serial.print(t);
+  Serial.println(" *C");
+
+  Serial.print("MQ5 waarde: ");
+  Serial.println(mq5Value);
+
+   Serial.print("TVOC "); Serial.print(sgp.TVOC); Serial.print(" ppb\t");
+  Serial.print("eCO2 "); Serial.print(sgp.eCO2); Serial.println(" ppm");
+
+  delay(500);
+}

src/C++/Driver/src/Sensors/Sensors.ino

@@ -1,59 +0,0 @@
-#include <DHT.h>
-#include <Wire.h>
-#include "Adafruit_SGP30.h"
-
-Adafruit_SGP30 sgp;
-
-// define pins and type of DHT sensor
-#define DHTPIN 4
-#define DHTTYPE DHT11
-#define MQ5_PIN 2
-#define SDA_PIN 10
-#define SCL_PIN 11
-
-DHT dht(DHTPIN, DHTTYPE);
-
-void setup() {
-  //initialize serial communication and the sensors
-  Serial.begin(9600);
-  
-  dht.begin();
-  
-  pinMode(MQ5_PIN, INPUT);
- 
-  Wire.begin(SDA_PIN, SCL_PIN);
-  Serial.println("SGP30 test");
-}
-
-void loop() {
-  float h = dht.readHumidity();
-  float t = dht.readTemperature();
-  
-  int mq5Value = analogRead(MQ5_PIN);
-
-  // if sensor isn't connected properly display error message
-  if (isnan(h) || isnan(t) || isnan(mq5Value)) {
-    Serial.println("Fout bij het lezen van de sensors!");
-    return;
-  }
-
-   if (! sgp.IAQmeasure()) {
-    Serial.println("Measurement failed");
-    return;
-  }
-
-  // puts sensor values in the serial monitor
-  Serial.print("Luchtvochtigheid: ");
-  Serial.print(h);
-  Serial.print(" %\tTemperatuur: ");
-  Serial.print(t);
-  Serial.println(" *C");
-
-  Serial.print("MQ5 waarde: ");
-  Serial.println(mq5Value);
-
-   Serial.print("TVOC "); Serial.print(sgp.TVOC); Serial.print(" ppb\t");
-  Serial.print("eCO2 "); Serial.print(sgp.eCO2); Serial.println(" ppm");
-
-  delay(500);
-}